NOVARIS PP10 SPECIFICATIONS
MODELS IN THIS SERIES : PP10-2 / PP10-4 / PP10-6 / PP10-8
MODES OF PROTECTION : FULL MODE (L-N, L-PE, N-PE)
NOMINAL VOLTAGE : 230V / 50Hz (110V / 60Hz available)
MAXIMUM CONTINUOUS VOLTAGE : 275V / 50Hz (130V / 60Hz)
MAXIMUM DISCHARGE CURRENT (8/20μs) : 13 A
PROTECTIOIN STAGES : METAL OXIDE VARISTOR / LC FILTER / METAL OXIDE VARSTOR
RESPONSE TIME : INSTANTANEOUS
POWER CONSUMPTION (@230V 50Hz) : <1W
EARTH LEAKAGE CURRENT : <200μA
CONNECTION TYPE : IEC C14 INLET
CONNECTION TYPE - LOAD SIDE OUTLET : UNIVERSAL / BRITISH (UK) (USA / AUS)
NUMBER OF OUTLETS : 2 / 4 / 6 / 8
ENVIRONMENTAL : IP20
WEIGHT : 1.3KG
DIMENSIONS : 2 / 4 / 6 / 8
W : 155mm / 205mm / 255mm / 305mm
H : 140mm
D : 60mm
CLASS LEADING SURGE PROTECTION WITH AC LINE POWER FILTER
Transient overvoltages superimposed on the AC mains are a major cause of electronic equipment failure. Most small surges go unnoticed but cause permanent degradation of electronic components, reducing their lifespan.
Damaging power surges can originate from many sources :
Novaris plug-in surge filter unit is a professional grade powerline filter and surge protection unit especially designed to improve the power quality for sensitive, expensive and critical equipment like :
Most surge protection power boards only provide a single layer of protection between your valuable equipment and damaging transient signals. The Novaris surge filter employs a 3-stage surge protection network to provide a premium level of protection.
For more information, download our brochure here.
MAJOR PROJECT REFERENCES
Major project reference list for consultancy, design, manufacturing/supply and installation of Lightning Protection Products and systems where the company or staff has participated
NOVARIS SFM / SFH
THE ULTIMATE BESPOKE POWER SYSTEM
Novaris SFM / SFH is a bespoke power surge protection system that provides excellent and effective MSB and DB protection for critical equipment from 40A to 125A per phase.
The SFM series utilize a 3 stage protection approach with 1st and 3rd stage MOV protection and a 2nd stage low pass LC filter.
SFM is also customisable for protection from 50kAmps to 200kAmps.
SFH models take over from 250A to 2,000Amps
SFH surge filters provide the highest level of protection with the lowest let through voltage.
When installed at a main switchboard Novaris surge filters will protect all connected equipment.
The SFH series utilize a 3 stage protection approach with 1st and 3rd stage MOV protection and a 2nd stage low pass LC filter.
Copyright © TRITONE AV PTE LTD. All rights reserved.
Novaris is an Australian company that specializes in building lightning protection devices. Mr. Philip Tompson, the founder of Novaris, explains the benefits for this one-of-a-kind surge filter, protecting sensitive equipment and the removal of noise.
ETHERNET / COMMUNICATION BASED SURGE PROTECTION
Novaris C-Bus™ RJ45 surge protection products are specifically designed for the protection of C-Bus™ RJ45 communications wiring, designed with primary protection elements of the C-Bus™ network pairs and secondary protection elements to provide protection for the Remote Override pairs.
The Novaris C-Bus™ protector contains integrated 230V isolation to prevent equipment damage during power to earth faults but also provide efficient earth bonding during a surge event.
ETHERNET / COMMUNICATION BASED SURGE PROTECTION
The RJ45-CAT6 and RJ45-PoE protection products employ a 10kA Gas Discharge Tube per signal pair to dissipate the energy associated with large common mode surges.The silicon based secondary protection element used on each signal pair provides exceptional protection for your equipment whilst allowing network speeds up to Gigabit/1000BaseT.
Local Area Network Protectors
Novaris network protection products are specifically designed for the protection of twisted pair Ethernet systems with a combination of rugged and one grain protection elements.
10kA Front End Protection & Low Impedance Secondary Protection
The RJ45-CAT6 protection products employ a 10kA Gas Discharge Tube per signal pair to dissipate the energy associated with large common mode surges.The silicon based secondary protection element used on each signal pair provides exceptional protection for your equipment whilst allowing network speeds up to Gigabit/1000BaseT. PoE,
PoE+, High Power PoE and beyond
The Novaris RJ45-CAT6 protection devices are designed to be compatible with PoE and handle up to 1 A of current per signal pair at up to 80VDC. This combination allows for Gigabit PoE systems with 4 pair power up to an outstanding 160W.
UTP and STP cabling compatible
Novaris network protection products utilise shield pass through connectors and metal bodies to allow for uninterrupted shielded network spans. The RJ45-1CAT6-EC90 option is necessary for earth isolation at the remote end of a network. This prevents current loops from appearing on the network shield.